Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE Stainless steel Applicability: Piper PA-18 MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET Allows installation of a rudder mounted anti-collision light or strobe light. Applicability: Piper PA-18 Material: Fiberglass and Aluminum Compatible with Whelen A470 and Grimes 30-0465-5 strobe lights Installation instructions and STC paperwork... MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE Attaches the shoulder harness to the fuselage frame thereby increasing safety of pilot and passengers during turbulence or accident. Fits 1-1/8 inch tubes Rear clamp-on bracket Material: Stainless steel Sold without seat belts Applicability: Piper... MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER Atlee's Safari Seat is approximately 14 lbs lighter than the stock Piper seat. The seat bottom is 13.5″ wide and the seat back is 11.5″ wide. Seat back folds forward to allow access to cargo area. Seat can be removed and replaced in seconds... MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING These metal springs replace bungee cords on the front safety cable assemblies of ski equipped airplanes to improve ski rigging tension in cold weather. See Atlee Dodge's installation instructions for other applicability requirements. Applicability:... MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET Allows installation of a rudder mounted anti-collision light or strobe light. Applicability: Piper PA-18 Material: Fiberglass and Aluminum Compatible with Whelen A470 and Grimes 30-0465-5 strobe lights Installation instructions and STC paperwork... MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE Attaches the shoulder harness to the fuselage frame thereby increasing safety of pilot and passengers during turbulence or accident. Fits 1-1/8 inch tubes Rear clamp-on bracket Material: Stainless steel Sold without seat belts Applicability: Piper... MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER Atlee's Safari Seat is approximately 14 lbs lighter than the stock Piper seat. The seat bottom is 13.5″ wide and the seat back is 11.5″ wide. Seat back folds forward to allow access to cargo area. Seat can be removed and replaced in seconds... MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING These metal springs replace bungee cords on the front safety cable assemblies of ski equipped airplanes to improve ski rigging tension in cold weather. See Atlee Dodge's installation instructions for other applicability requirements. Applicability:... MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE Attaches the shoulder harness to the fuselage frame thereby increasing safety of pilot and passengers during turbulence or accident. Fits 1-1/8 inch tubes Rear clamp-on bracket Material: Stainless steel Sold without seat belts Applicability: Piper... MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER Atlee's Safari Seat is approximately 14 lbs lighter than the stock Piper seat. The seat bottom is 13.5″ wide and the seat back is 11.5″ wide. Seat back folds forward to allow access to cargo area. Seat can be removed and replaced in seconds... MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING These metal springs replace bungee cords on the front safety cable assemblies of ski equipped airplanes to improve ski rigging tension in cold weather. See Atlee Dodge's installation instructions for other applicability requirements. Applicability:... MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER Atlee's Safari Seat is approximately 14 lbs lighter than the stock Piper seat. The seat bottom is 13.5″ wide and the seat back is 11.5″ wide. Seat back folds forward to allow access to cargo area. Seat can be removed and replaced in seconds... MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING These metal springs replace bungee cords on the front safety cable assemblies of ski equipped airplanes to improve ski rigging tension in cold weather. See Atlee Dodge's installation instructions for other applicability requirements. Applicability:... MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING These metal springs replace bungee cords on the front safety cable assemblies of ski equipped airplanes to improve ski rigging tension in cold weather. See Atlee Dodge's installation instructions for other applicability requirements. Applicability:... MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE This modification adds a fueling step to the outside of the front strut of the main landing gear. No more step ladder for refueling! Applicability: Piper J-3, J-4, J-5, PA-11, PA-12, PA-14, PA-15, PA-16, PA-18, PA-20, PA-22 Clamp-on refueling step... MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors. If lift strut fitting is bent or has elongated holes it will need to be replaced. Applicability: Piper... MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER This defroster kit has its own diverter box, control and outlets. It is installed AFT of the cabin heat box on the inside of the cockpit. Installation time varies from 4 to 8 hours depending on the aircraft. The kit uses 2 inch CEET hose and works very... MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 This heater kit modification provides heating to rear seat passengers. A must have for Super Cubs in winter! Applicability: Piper PA-18 with Lycoming engines Diverter box and push pull cables are stainless steel, hoses are 2″ CEET and 2″... MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approval (SA02188AK for PA-12/14, SA02152AK for PA-18) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT Applicability: Piper PA-12, PA-14, PA-18 Landing gear 1.25" axle, 3" extended length STC approved (SA02152AK, SA02188AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT 1.25 inch axle, standard length Applicability: Piper J-3, PA-11, PA-18, PA-19 PMA approval Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the lower gear legs Does not come with axle nut... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT Landing gear 1.5" axle, 3" extended length Applicability: Piper PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT Landing gear 1.5" axle, 3" extended length Applicability: PA-12, PA-14, PA-18 STC approved (PA-12, PA-14: SA02188AK; PA-18: SA02152AK) Comes with bushings installed in forward and aft upper attach fittings & gussets and doublers supporting the... MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 Applicability: Piper PA-18 Material: 4130N Steel STC approved (SA4618NM) Heavy duty replacement for Piper part numbers 30602-010 and 30602-007 MSRP: Now: $544.00 Add to Cart Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3359-6 3359-6 WATER RUDDER PICKUP TUBE MSRP: Now: $64.00 Add to Cart Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 2087 2087 RUDDER STROBE LIGHT MOUNTING BRACKET MSRP: Now: $401.00 Add to Cart Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3232-2-1-1/8 3232-2-2-1/8 SHOULDER HARNESS ATTACH BRACKET - REAR - 1.125 INCH TUBE MSRP: Now: $228.00 Add to Cart Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 6151 6151 SAFARI SEAT - FITS PIPER MSRP: Now: $969.00 Add to Cart Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 2127 2127 PIPER PA-18 GOLD AIRCRAFT SKI SPRING MSRP: Now: $249.00 Add to Cart Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3190-10 3190-10 REFUELING STEP - 1.25 INCH TUBE MSRP: Now: $152.00 Add to Cart Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3192-18DL 3192-18DL FRONT LIFT STRUT REINFORCEMENT BRACKET MSRP: Now: $166.00 Add to Cart Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3242-18 3242-18 UNIVERSAL DEFROSTER KIT - FITS PIPER MSRP: Now: $1,043.00 Add to Cart Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3175 3175 REAR SEAT HEATER KIT - FITS PIPER PA-18 MSRP: Now: $1,021.00 Add to Cart Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3225-2 3225-2 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-1 3284-1 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-2 3284-2 PIPER LANDING GEAR 1.25 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3225-1 3225-1 PIPER 1.25 INCH AXLE STANDARD LANDING GEAR - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-1A 3284-1A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - LEFT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next × OK
Atlee Dodge | part number: 3284-2A 3284-2A PIPER LANDING GEAR 1.5 INCH AXLE, 3 INCH EXTENDED - RIGHT MSRP: Now: $1,110.00 Choose Options Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next
Atlee Dodge | part number: 3166-1 3166-1 HEAVY DUTY CABANE VEE - FITS PIPER PA-18 MSRP: Now: $544.00 Add to Cart Previous 1 2 3 4 5 Next Previous 1 2 3 4 5 Next
